TEE AND BRANCHES FITTINGS
  
  
Feedback
 
Pipe Fitting
FEATURES :

1) Material : Stainless Steel & any Ductile Material
2) Size : 1" NB to 6" NB & 25MM to 152MM
3) Polished Finish Condition
4) Tailor Made extension / Reducer / Fitting.
5) Electro Polishing / Mat Finishing as per requirements.

NB SIZE
A
B±1.0 MM
C±1.0MM
25 NB
1.65
44.00
3 To 4
40 NB
1.65
62.50
4 To 5
50 NB
1.65
62.50
4 To 5
63 NB
2.00
80.00
4 To 6
100 NB
2.00
108.00
4 To 6
150 NB
3.00
130.00
Upto 7

Feedback

   
Conflact Flanges
MF BLANK FLANGE
  A T
16 MF 34.0 7.6
35 MF 70.0 12.7
63 MF 114.0 17.2
100 MF 152.0 19.5
150 MF 203.0 22.3
200 MF 254 24.6
Material:- SS304 / 304L

MF FIXED FLANGE (WELD)
  T D
16 MF 7.60 20.5
35 MF 12.7 38.2
63 MF 17.2 63.5
100 MF 19.5 102.1
150 MF 22.3 153
200 MF 24.6 203
Material:- SS304 / 304L
MF ROTATABLE BLANK FLANGE
  B T
16 MF 20.5 7.6
35 MF 39.5 12.7
63 MF 65.0 17.2
100 MF 103.5 19.5
150 MF 154.5 22.3
200 MF 204.5 24.6
Material:- SS304 / 304L

The reliable sealing performance of Conflact flanges is a result of the design and geometry which "Captures" the gasket material. When the conical sealing knife edge of the flange is pressed in to the flat OFHC copper gasket, a lateral cold flow of the gasket material occurs. This cold flow is limited by the vertical flange wall.

Further material flow away from the seal area is severely limited and high interface pressures are developed. These pressures cause gasket material to fill surface imperfections and produce a highly reliable seal. At high temperatures, the "Capturing" Geometry maintains high pressures despite softening of the gasket.


Specifications
Materials 304 ss / 304L
Flanges
Gasket Copper / Viton
Metal 304 ss / 304L
Temperature Range
Conflact -200oC to 450oC
Vacuum Range
Conflact 10-10Torr

Feedback

 

The 3II Whole Body Consumer Commissioned At
(NATIONAL INSTITUTE OF NUTRITION HYDERABAD)


The new whole Body Monitoring Facility for low level counting set-up at NIN opens up a new phase of research activity at the Institute with a wide range of potential applications. The new facility is a 3II counter where the subject/patient is counted in a stationary geometry under low level back ground condition in a steel room and an efficient ventillating system.

Steel room : The detectors of the WBC facility are set up in a steel room. The steel room is housed in an air-conditioned hall of dimension 6m x 5 x 5 meters. It is erected on a special platform reinforced with concrete and MS plates. It has dimension of 2 x 2.7 x 2 meters. The steel thickness on four sides of the wall (including door on one side) and top is 150 mm and at bottom it has a thickness of 225 mm. All the construction materials, like Steel, lead, copper, sand, brick, cement were tested for their low background and approved by BARC for their acceptability. Inside the steel room, there is a 10 mm layer of lead bricks fixed to steel plates. Over this lead brick is one mm thickness of copper sheet layered around. The various thickness of steel sheets were washed with distilled water and coated with "suprap" an anti-corrosion agent. The joints are argon welded. The door mechanism of the steel room is erected on special rails and the doors are supported by Taylor bearings imported specially for this purpose. They slide on a stainless steel rod. The door can be slided either way and it is easy to handle. A manually operated door system was preferred to avoid any emergency situation in the case of an electrically operated doors due to power failure.

Mechanical Attritor
 

Mechanical Attritor shall be used for grinding of metal powder. It consists of a water cooled vessel with an armed shaft. This  shaft assembly is rotated with the motar- gear box. After completion of grinding operation ground powder can be taken out from the bottom in a container

 VACUUM PRODUCTS RANGE

1. CONFLACT FLANGES WITH FITTINGS : SIZE : MI-34 TO MI -252

1. Non Rotatable Blank / Bored
2. Rotatable Blank / Bored
3. Double Side flange
4. Smaller and Reducer Flanges
5. Flange Adopter
6. Tube , 4-way, 6-way fittings.
7. ETC.,

2. ISO FLANGES & FITTINGS : SIZE : MI-100 TO MI-250

1. KF-10 to KF-200 fittings.
2. Centre Ring Assemblies.
3. Socket weld Flanges M-16,25,40,50.
4. Weld fittings : M-16,25,40,50.
5. Long & Short weld stub Flanges.
6. Flexible coupling.

3. WELD FITTINGS
1). TEE  2). 4-WAY CROSSESS  3). 5-WAY CROSSESS  4). 6-WAY CROSS.


4. ASA FLANGES & FITTINGS
1). SIZE : 4 " to 12" .     2).  Flange Adopters.

5. ULTRA HIGH VACUUM GATE VALVE : MANUALLY:
C SIZE : 1). 2".   2). 3" .    3). 4".    4). 5" & 6".

6. RIGHT ANGLE VALVE : MANUALLY
SIZE : 1" TO 4"

7. BUTTERFLY VALVES : MANUALLY
SIZE : 1). 1".    2) .2" . 3)  3". 4)  4" & 6"

8. GLASS VIEW PORT :
ACCORDING TO USERS SIZES.

9. VACUUM CHAMBERS AS PER YOUR DESIGN

10. ETC.

Registration No: D-U-N-S. No. 65-071-8547 Dt. 23-7-98

 
 
Company Profile | Product | Technology | Photo Gallery | Turnkey Project | Customer List | Feedback